How to Create a Tech Pack for Custom Sportswear (With Checklist)
What a sportswear tech pack must contain, artwork file rules for sublimation (vector, 150-300 dpi), a factory checklist and what to do if you have none.
Vofit Design Team
Vofit Custom Sportswear
The Short Answer
A tech pack is the document set that tells a factory exactly what to make: flat sketches, a measurement chart with tolerances, a bill of materials, colourways with Pantone references, artwork placement, labels and packaging. For sublimated sportswear, artwork should be supplied as vector AI or PDF files, with any raster images at 150–300 dpi at full print size. A complete tech pack usually means one sample round instead of two or three, and if you do not have one, a factory can work from a reference sample or an ODM design instead.
What a Tech Pack Is and Why Factories Ask for One
A tech pack (technical package) is a specification, not a mood board. Every decision that is not written down gets made by someone on the factory floor, and their default may not be yours: the stitch type, the label position, the shade of navy.
It does not need special software. Many good tech packs are a 5–10 page PDF or a tidy spreadsheet with drawings pasted in.
The Seven Parts of a Sportswear Tech Pack
1. Flat sketches
Flats are black-and-white technical drawings of the garment laid flat, showing front, back and, where relevant, side and inside views. They show every seam, panel, pocket, zip, hem and stitch line in proportion. Add call-outs for construction details: "flatlock seams", "raglan sleeve", "5 cm elastic waistband with internal drawcord", "silicone gripper at hem".
2. Measurement spec and size chart
This is the part most often missing and most often responsible for failed samples. List each point of measure (POM) with a short description of how it is measured, the value for every size, and the tolerance.
| Point of measure | S | M | L | XL | Tolerance |
|---|---|---|---|---|---|
| Chest width, 2 cm below armhole | 49 | 52 | 55 | 58 | ±1 cm |
| Body length from high shoulder point | 68 | 70 | 72 | 74 | ±1 cm |
| Sleeve length from shoulder seam | 20 | 21 | 22 | 23 | ±0.5 cm |
The figures above are an illustration for a men's training tee, not a standard. Typical knitwear tolerances are ±1 cm on body measurements and ±0.5 cm on small ones. Say whether your sizing is US, UK, EU or Asian fit, because an "M" differs by a full size between regions.
3. Bill of materials (BOM)
The BOM lists every physical component:
- Main fabric: composition, knit and weight, for example "polyester interlock 140 GSM" or "nylon-spandex 80/20, 250 GSM"
- Secondary fabrics: mesh panels, rib collars, linings, pocket bags
- Trims: zips (type, length, puller), elastic, drawcords, eyelets, silicone grippers, bra pads, chamois pads
- Labels, hang tags and packaging materials
If you do not know the exact fabric, describe the performance you want and ask the factory to propose options. Vofit's fabric guide lists the fabrics normally stocked for each product type.
4. Colourways with Pantone references
Screens are not colour standards. Give a Pantone code for every colour in every colourway: Pantone TCX or TPG for dyed fabrics and trims, and Pantone Solid Coated (C) for printed artwork.
5. Artwork placement
Show each logo, number, sponsor mark and pattern on the flat sketch with its size and position measured from a fixed point: "chest logo 9 cm wide, centred, top edge 7 cm below neck seam". State the decoration method for each element — sublimation, screen print, heat transfer or embroidery — because the method changes both the file needed and the price. At Vofit the per-piece surcharges are $1.50 for sublimation, $0.80 for screen print, $0.50 for heat transfer and $2.00 for embroidery. Our printing methods page compares them.
6. Labels
Specify the neck label (woven, printed or heat-transferred), the care label and its position, and the content each must carry: brand, size, fibre composition, care symbols and country of origin. Labelling rules differ between the US, UK, EU, Canada, Australia and Japan, so confirm the requirements for your market. For branded labels and hang tags, see private label options.
7. Packaging
State how each piece is folded and bagged, whether polybags need a size sticker or barcode, how many pieces go in a carton, and any carton marking your warehouse or marketplace requires.
Artwork File Requirements for Sublimation
Sublimation prints whole fabric panels before sewing, so files that look fine on screen can fail at full size.
- Vector first. Supply logos, text, numbers and geometric patterns as vector artwork in AI, PDF or EPS.
- Outline fonts. Convert all text to outlines, or send the font files, so nothing is substituted.
- Raster resolution. Photographs and textured graphics should be 150–300 dpi at full print size. A 1,000-pixel image stretched across a 60 cm jersey front is about 42 dpi and will print blurred.
- Colour mode. Sublimation uses CMYK-based inks. Artwork built in RGB can contain bright greens, oranges and blues that cannot be printed, so work in CMYK or expect those colours to dull.
- Pantone targets. Tag key brand colours with Pantone codes. A strike-off confirms the result on fabric.
- Blacks. Ask the factory for its preferred rich black build; a plain 100% K black can look grey on polyester.
- Bleed and seams. Extend backgrounds past the pattern edge, and keep small text and logos at least 1.5–2 cm away from seams, zips and hems.
PNG or JPG files are acceptable only as visual references. If all you have is a low-resolution logo, say so: Vofit offers free design support and can redraw it as vector before sampling.
Tech Pack Checklist: What the Factory Needs and Why
| Item | Why the factory needs it |
|---|---|
| Front and back flat sketches | To make the pattern and identify every seam and panel |
| Size chart with POMs | To grade the pattern across all sizes |
| Tolerances | To set the pass/fail standard for quality control |
| Fabric composition and GSM | To source the right fabric and price the garment |
| Trim list | To order zips, elastics and pads with their own lead times |
| Pantone codes per colourway | To dye or print to a measurable colour target |
| Vector artwork files | To print sharply at full panel size |
| Decoration method per element | To quote correctly and plan production steps |
| Label and hang tag details | To produce branding and meet labelling rules |
| Quantity per size and colour | To calculate fabric usage and confirm MOQ and price tier |
| Target price and delivery date | To suggest alternatives if the spec exceeds the budget |
What to Do If You Have No Tech Pack
Plenty of first-time buyers, clubs and small brands do not have one. There are three routes.
- Start from an ODM style. Pick an existing factory design and customise fabric, colours, artwork and labels. The pattern and grading are already proven. This is how Vofit's ODM design service works.
- Send a reference sample. Post a garment whose fit you like. The factory measures it, copies the pattern and builds the spec from it. Note anything you want changed, such as "2 cm longer body".
- Send a design brief. A sketch or annotated photo, your logo files, colour codes, a size range and target quantity are enough for a factory design team to draft the mock-up and spec for your approval.
If you already have full designs and want them produced exactly as drawn, that is OEM manufacturing, and a complete tech pack matters most there.
How a Complete Tech Pack Shortens Sampling
Every missing detail becomes a question that costs a day across time zones, or surfaces only when the sample arrives.
Vofit makes samples in 5–7 days, and express shipping typically takes 3–7 days door to door. Each extra revision round therefore adds roughly 8–14 days before bulk production can start. With a complete tech pack, the first sample is normally close enough that corrections can be confirmed with photos, and bulk production of 100–499 pcs can follow in 7–12 days. With a vague brief, two or three rounds are common.
Frequently Asked Questions
Do I need a tech pack to order custom sportswear?
No. A tech pack is the fastest and most precise route, but a factory can also work from a reference sample, an ODM style or a clear design brief with logo files and colour codes. You will still need to approve a size chart and a mock-up before sampling.
What file format should sublimation artwork be in?
Vector AI, PDF or EPS files with fonts converted to outlines are the standard. Any photographic or raster elements should be 150–300 dpi at the actual print size. JPG and PNG files work as references but often need to be redrawn before printing.
Should I use RGB or CMYK for sportswear artwork?
Use CMYK and add Pantone references for key brand colours. RGB files can include colours that sublimation inks cannot reproduce, so bright screen colours come out duller on fabric. A printed strike-off is the only reliable way to confirm colour before bulk.
Who owns the tech pack and the pattern?
If you create and supply the tech pack, the design is yours. When a factory develops the pattern from your brief or adapts its own ODM style, ownership and exclusivity should be agreed in writing before sampling. Ask the question early rather than assuming.
Send Us What You Have
A full tech pack, a reference garment or a rough sketch with a logo are all enough to start. Upload your files through the quote form and Vofit will confirm what is missing, the price and the sample timeline.
Ready to Start Your Custom Sportswear Order?
Get a free quote with no obligation. We respond within 12 hours.
Get Free Quote