Business 2026-11-22 · 8 min read

Sportswear Size Charts: US, EU, UK and Asian Sizing Explained

Why a US M is not an Asian M, how to grade a size chart in 5 cm steps, what tolerances to set, plus conversion and garment measurement tables.

VDT

Vofit Design Team

Vofit Custom Sportswear

The Short Answer

There is no legally binding size standard for sportswear, so a medium in the US, UK, EU and Asia can differ by one to two full sizes. As a rough guide, a US or UK men's M fits a 96-102 cm chest, corresponds to EU 48-50, and is closest to an Asian L or XL. The reliable way to avoid returns is to ignore the letter on the label and specify garment measurements in centimetres, graded in steps of about 5 cm on the chest between sizes, with a tolerance of about 1 cm on the main measurement points.

Why Sizes Differ Between Markets

Size labels grew out of national habits, not out of one shared system.

  • Different body data. Each market's sizing is based on its own population surveys. Average height, chest and hip measurements differ between North America, Northern Europe and East Asia, so the "middle" size is built around a different body.
  • Different labelling systems. The US and UK use letters and, for women, numbers that are offset from each other (a US 6 is roughly a UK 10). Continental Europe uses numbers based on half the chest in centimetres for men and its own scale for women. Japan and China often label by height and chest, such as 175/92A.
  • Vanity sizing. Many Western brands have gradually made each labelled size larger. Two US brands can differ by 5 cm on the same size.
  • Fit preference. Buyers in the US often expect a looser training fit than buyers in Japan or Italy for the same activity.

A factory's "standard size chart" is only standard for that factory's main market, so ask which market it was built for.

Body Measurements vs Garment Measurements

These are two different charts and mixing them up is the most common cause of a wrong-size bulk order.

A body measurement chart tells the customer which size to buy: chest, waist, hip and height of the person. It goes on your website.

A garment measurement chart (also called a spec sheet) tells the factory what to cut: half chest, body length, shoulder width, sleeve length and so on, measured with the garment laid flat. It goes in your tech pack.

The gap between the two is called ease. A relaxed tee for a 100 cm chest might measure 110 cm around, which is 10 cm of positive ease. A compression top for the same person might measure 88 cm, which is negative ease, because the fabric is meant to stretch on the body.

Indicative Size Conversion Tables

These tables are indicative only. Brands differ, and they should never replace a measurement chart for your own product.

Men's and unisex tops

US / UKChest (cm)Chest (in)EUClosest Asian label
XS81-8632-3442-44M
S86-9134-3644-46L
M96-10238-4048-50L-XL
L107-11242-4452-54XL-2XL
XL117-12246-4856-582XL-3XL
2XL127-13250-5260-623XL-4XL

Women's

LetterUSUK / AUEUJapan
XS0-24-632-345
S4-68-1036-387-9
M8-1012-1440-4211-13
L12-1416-1844-4615-17
XL16-1820-2248-5019-21

France, Italy and Spain use numbers offset from the general EU scale, another reason to publish centimetres.

How to Build a Size Chart for Your Brand

  1. Pick your target customer and market. A chart for US college athletes and one for a Japanese running club should not be the same.
  2. Choose a base size. Usually M for men and S or M for women. This is the size your sample is made in and fitted on a real person.
  3. Perfect the base size. Adjust the sample until the fit is right, then record the final garment measurements at every point.
  4. Apply grading increments. Grading is the rule for how much each measurement changes from one size to the next.
  5. Set tolerances. Decide how far a finished garment may deviate and still pass inspection.
  6. Check the extremes. Make or at least measure the smallest and largest sizes; errors in grading show up there first.

Typical grading increments

For adult knit tops, common increments per size are 5 cm on chest circumference (2.5 cm on the flat half-chest), 2 cm on body length, 1-1.5 cm on shoulder width and 1 cm on short-sleeve length. Many brands widen the chest step to 6-7 cm from XL upwards. For leggings and shorts, waist and hip usually grade by 4-5 cm per size, while inseam changes by 1 cm or stays constant.

Example: garment measurements for a men's training tee

Regular fit, 160gsm polyester, measured flat in centimetres.

Measurement pointSMLXL2XLTolerance
Half chest (2.5 cm below armhole)5052.55557.560+/- 1
Body length (high shoulder point to hem)6971737577+/- 1
Shoulder width (seam to seam)4344.54647.549+/- 1
Sleeve length (shoulder seam to cuff)2021222324+/- 0.5
Hem width4951.55456.559+/- 1
Neck width1818.51919.520+/- 0.5

This shows the format, not a recommended chart. Vofit uses the same structure for a custom gym T-shirt or a running T-shirt.

Tolerances

Knitted sportswear is sewn from stretch fabric on hand-guided machines, so no two pieces are identical. Normal tolerances are about 1 cm on chest, length and hip, 0.5 cm on smaller points such as neck, cuff and sleeve opening, and up to 1.5-2 cm on long measurements in very stretchy fabrics. Write the tolerance next to every measurement point.

Fit Types Change the Numbers

Compression vs relaxed fits

A compression garment is cut smaller than the body, typically 10-20% less in circumference, and relies on fabric with high stretch and recovery such as nylon-spandex 80/20. The reduction depends on the fabric's stretch, so a pattern proven in one fabric cannot simply be reused in another. A relaxed or regular fit adds 8-15 cm of ease on the chest. A basketball jersey is usually cut with more ease than a cycling jersey, which sits close to the body to reduce drag. State the intended fit on your size chart.

Unisex vs women's cuts

A unisex garment is in practice a men's block: straight side seams, wider shoulders, longer body. A women's cut has narrower shoulders, a shorter body, shaping at the waist and more room at the bust and hip. If you offer unisex only, tell women to choose one size down from their usual women's size and publish the garment measurements.

Youth sizes

Youth sizing is the least consistent of all. The US uses YS-YXL, the UK labels by age (7-8, 9-10, 11-12), and Europe and Asia label by height in centimetres (110 to 160, in steps of 10). Height-based labelling is the most reliable. Youth sizes need their own grading: length grows faster than width, so adult increments scaled down will not fit.

How a Manufacturer Uses Your Size Chart

At Vofit the chart drives four steps. The pattern maker drafts the base-size pattern from your garment measurements, and the pattern is then graded digitally to the other sizes using your increments. A sample is sewn, usually in 5-7 days, and measured against the chart before it is sent to you. After you approve it, the approved measurements and tolerances become the inspection standard for bulk production.

If you have no chart, either send a garment whose fit you like to be measured, or start from the factory's chart for your market and adjust it after the first sample. Both are covered by Vofit's OEM manufacturing service, and free design support includes help with the spec sheet.

Collecting Sizes for a Team Order

  1. Send every member the garment measurement chart, not just S/M/L, and ask them to compare it with a shirt they already own, laid flat.
  2. If the club is large, order a size-run sample set first so people can try sizes on.
  3. Collect sizes in one spreadsheet with name, number, size and cut (men's, women's, youth) on one line per person.
  4. Set a firm deadline and one person responsible for the final list.
  5. Add a few spares in the most common sizes; reordering one or two shirts later is rarely possible below the 30-piece teamwear minimum.

Frequently Asked Questions

Is an Asian size smaller than a US size?

Generally yes, by one to two sizes. A US men's M with a 96-102 cm chest is usually closest to an Asian L or XL. Because brands and factories differ, compare garment measurements in centimetres instead of relying on the label.

What is a grading increment?

It is the amount a measurement changes between neighbouring sizes. For adult sportswear tops a typical increment is 5 cm on chest circumference and 2 cm on body length per size. Increments are applied to the fitted base size to produce the full size range.

What measurement tolerance is acceptable for sportswear?

About 1 cm on main points such as chest and body length and 0.5 cm on small points such as neck and cuff is normal for knitted sportswear. Very stretchy fabrics and long measurements may be given 1.5-2 cm. The tolerance should be written into the spec sheet before production.

Should I use the factory's size chart or my own?

Use your own if you have a proven fit, because it keeps sizing consistent across suppliers and seasons. If you are starting out, begin with the factory's chart for your target market, order a sample, and adjust the measurements before bulk production.

Send Us Your Size Chart

Upload your size chart, tech pack or a photo of a reference garment through the quote form and Vofit will confirm whether it can be graded as is or needs adjusting for your fabric. If you have no chart yet, tell us your target market and fit and we will propose one with your quote.

Ready to Start Your Custom Sportswear Order?

Get a free quote with no obligation. We respond within 12 hours.

Get Free Quote